Product Picture Master

thermosept® PAA additive

Active oxygen-based disinfection of flexible endoscopes

Our Plus

  • effective against bacteria, mycobacteria, fungi, viruses
    and spores (incl. Clostridium difficile spores)
  • good material compatibility due to a 2-component system
  • short contact time

Downloads

Product Brochure, PDF [4.3 MB] 
Open allClose all

Fields of Application

For the automated chemothermal reprocessing of flexible endoscopes in AERs.
thermosept® PAA base/additive is suitable for the use in all common AER systems which are released for the use of peracetic based products.
Bactericidal, tuberculocidal, mycobactericidal, fungicidal, virucidal (in accordance with DVV/ RKI Guideline** 12/2014 and EN 14476, EN 17111), sporicidal (Clostridium difficile spores) at 1.0 % - 37 °C - 5 minutes or 1.2 % - 35 °C - 5 minutes.

Instructions for use

• Dosage: 1 % (10 ml/l) - 37 °C or 1.2 % (12 ml/l) - 35 °C
• Whenever possible, simultaneously dose thermosept® base and thermosept® additive. If the AER metering pumps are unable to dose the two components simultaneously, add thermosept® PAA base and then thermosept® PAA additive immediately thereafter. Ensure that this order is followed so as to guarantee material compatibility.
• The contact time is 5 minutes.
• Disinfection components are compatible with the mild alkaline cleaning agent thermosept® EndoCleaner. Approved microbiological compatibilty.

Certificates / Norms

0297

Product data

Composition, base component: 100 g of solution contain: 5 g of peracetic acid, hydrogen peroxide and acetic acid
Composition, additive component: 100 g of solution contain: potassium hydroxide, phosphates and corrosion inhibitors
Labelling according to Regulation (EC) No. 648/2004: < 5 % phosphates

Chemical-physical data

Color
light yellow
Density
ca. 1,2 g/cm3 / 20 °C
Flash point
Not applicable
Form
liquid
pH
> 13
Viscosity, dynamic
No data available
Odor
odourless

Special advice

The base and additive components have to be used in combination. Store in original container at room temperature. Keep the container tightly closed. Protect from heat and sunlight. thermosept® PAA is not suitable for instruments made of brass and copper or chrome-plated instruments. According to EN 17664, the instrument manufacturers' instructions should be followed and, if necessary, the compatibility of the materials ensured before the application. This applies in particular when reprocessing older endoscopes. These should be strictly tested for compatibility with peracetic acid. For professional use only. Read label and use instructions before use.

Information for order

ItemDelivery formItemGTIN
thermosept PAA additive BHT Pin 5 l KA2 / carton(s)700008814032651960620
thermosept PAA additive 5 l KA2 / carton(s)1258024032651258024

Related products

Environmental information

schülke manufactures products economically and with advanced, safe and environmentally friendly production processes while at the same time maintaining our high quality standards.

Privacy Policy

We use analysis methods (e. g. cookies) to measure how often our site is visited and how it is used. In addition, we use cookies to link your page visits and website use with your customer data stored in our CRM system in order to be able to address you individually, i.e. based on interests and usage. We embed third-party content from other providers (e. g. videos) on our site. We have no influence on further data processing and any tracking by the third party provider. In this context, we also use service providers in third countries outside the EU that may not have an adequate level of data protection, which harbors the following risks: Access by authorities without informing the data subject, no data subject rights, no legal remedies, loss of control.
With your settings you consent to the processes described above. You can revoke your consent with effect for the future. You can find more information in our privacy policy.

Imprint